MF-22 Build Video Part 3

by MESA RC | November 26, 2013 | (14) Posted in Projects

 

To the FliteTest Community;

In the previous article, Colton showed off the MF-22 maiden and the plane did exceptionally well. Hoping that this plane would be download a few times, and the questions would be rolling in on how do you build this plane, Colton put together a build video showing viewers how to go about creating the plane. Step by step he shows how to construct the plane, with the exception of placing on equipment for the sake of time. If you would like to see how he accomplished this, please visit our Wolverine build, he used this approach to mount his servos.

http://youtu.be/sXJvSwm8BQM

For more information about the MESArcFF Program: http://www.mesarcfoamfighters.com/

Recommended Parts:

This is listed on the cover sheet of the plans:

 

We also have our own page that references parts that we recommend:

http://www.mesarcfoamfighters.com/#!curriculum-used-rc-partz/c1u49 

 FULL SIZE PLANS: http://media.wix.com/ugd/fe25e6_bf4b3cc10d654644984229b8d68c4d6b.pdf

Thanks and enjoy,

 

On the plans, all lines marked in RED are fold lines, RED lines that have no GREEN lines around them are just fold lines, no bevel required.

 

Lines marked GREEN indicate that a bevel needs to go there in order to fold the foam board to its desired shape.

 

All notches in this plane should not be cut through, however, they should be cleaned out, we like to use a flat head screw driver seen here.

 

Beveling seen here.

 

Place glue inside the fold/bevel lines to form the fuselage seen here.

 

Our customized motor mount helps keep the form of the fuselage as well.  To download our motor mount plans, please use the following link: http://media.wix.com/ugd/fe25e6_8b2472256d6e20827cdec52d3fe26abd.pdf 

 

Drifit the top plate on the fuselage to insure everything is straight.

 

Use masking tape to help seam fuselage nose piece to form.

 

Make sure the top plate is inline with the motor cutout section of the bottom plate, glue down.

 

This step could happen anytime you have the fuselage piece completed, Colton choose to insert the motor in during this stage.

 

Example of glueing the seams for stronger construction.

 

The wing supports are very important, they allow the wing to grab onto the top and bottom plate pieces for better construction.

 

The glueing of the wings is tricky, take your time, sandwhich it in, and make sure they are both equal to each other and perpendicular off the fuselage piece.

 

As you see here, glue the top first, then the bottom piece to the wings.

 

Constantly checking to make sure the wing is straight.

 

Another shot of the back of the plane.

 

Place the stabilzers in the notch shown on the video and place at a 45 degree angle.  Make or use the template provided in the plans for this application.

 

For servos, please see Wolverine Build video for this process http://flitetest.com/articles/Wolverine_Build

The canopy is beveled on almost every edge and glued together, to see this process please visit link above.

 

Hope you had fun with the build, now go ahead and fly the bird!

COMMENTS

Royall on November 26, 2013
Great video! Great plane too! Keep up the good work!
Log In to reply
Flying Penguin RC on November 28, 2013
Great job Colton, keep up the good work,
can't wait to see your next plane.
Log In to reply
btallis on November 26, 2013
Wow! Great build video, MesaRCFF! I was very impressed with the quality of the build video. Colton, I might just have to make one of these planes. Looks like a lot of fun to build and fly. Pretty challenging build, but you guys made it look possible. Also, great camera work! Thanks guys...
Log In to reply
flight monkey on December 1, 2013
Awsome build !!!!!! I have been waiting for a Real F22 build. ( I dont care much for the profile builds ). I will be building this plane, which means another week sober.Thanks for the free plans!
Log In to reply
spetnazer on August 6, 2014
Hi...this time I'm making this plane ... but I am confused when to put the servo. because there are No in plans. if anyone can help?
how servo is used? and section anywhere? anyone can help by providing a video tutorial?
Thank u very much
Log In to reply

You need to log-in to comment on articles.


MF-22 Build Video Part 3